Motor Matched E Bike Wheel Lock OEM Smart Bicycle Back Wheel Lock
| Model: | HS3718 / DS3710 / GS3646 | Application: | E-Bikes / Electric Scooters / Hub Motor Mobility Platforms |
| Selection Logic: | HS3718 For Compact Standard Use / DS3710 For Higher Torque / GS3646 For Larger Axle-Hole And Higher Temperature Direction | Installation Value: | Inside Rear Hub Motor, Motor Matching Required |
| Control Interface: | UART / RS485 / CAN According To Reference Products | Axle Hole Direction: | 15 X 15 Mm Reference Structure |
| Speed Sensing Distribution: | Defined By Customer Requirement / Motor End Cover | Waterproof Rating: | IPX6 |
| High Light: | e bike wheel lock oem,motor matched e bike wheel lock,oem bicycle back wheel lock |
||
The Motor-Matched Smart Wheel Lock is designed for OEM e-bike and scooter projects where the hidden wheel lock must be selected according to the rear hub motor structure. Instead of treating all motor hub locks as interchangeable, this page helps buyers compare compact, high-torque and high-temperature directions.
HS3718, DS3710 and GS3646 share the same basic product category and hidden rear hub motor installation concept, but they are not the same configuration. The correct choice depends on axle-hole structure, torque requirement, operating temperature, motor end-cover design and vehicle-side control architecture.
This buyer-intent page is useful for OEM procurement and engineering teams that need to discuss motor matching before requesting samples. It keeps the reference parameters separate so buyers can evaluate the right direction without confusing the three models.
- Motor-Matched Selection: Created for OEM teams selecting hidden wheel locks by motor structure rather than generic lock type.
- Three Reference Directions: HS3718 for compact standard use, DS3710 for higher torque, GS3646 for larger axle-hole and higher temperature requirements.
- Hidden Rear Hub Motor Installation: All three reference products are installed inside the rear hub motor and require motor matching.
- Smart Vehicle Control: Supports vehicle-side integration through the source-listed communication interfaces.
- Comparison-Based Specification: Parameters are shown as model comparison instead of one blended product table.
- OEM Validation Required: Motor end cover, sensor layout, axle hole and controller protocol should be confirmed before sampling.
Hidden motor hub locks work inside the rear hub motor structure and respond to vehicle-side lock or unlock commands. Because the lock is integrated with the motor, mechanical layout and electronic matching are both part of the product selection process.
The core technical decision is choosing the right reference direction. HS3718 is the compact standard direction, DS3710 increases torque resistance while keeping the 15 x 15 mm axle-hole direction, and GS3646 uses a larger axle-hole direction with higher temperature positioning.
This product page is suitable for OEM e-bike platforms, electric scooters, shared mobility vehicles and hub motor projects that need hidden wheel security selected according to motor structure and project requirements.
| Parameter | HS3718 | DS3710 | GS3646 |
|---|---|---|---|
| Product Name | Compact E-Bike Wheel Lock | High Torque E-Bike Wheel Lock | High Temperature E-Bike Wheel Lock |
| Model | HS3718 | DS3710 | GS3646 |
| Product Category | E Bike Wheel Lock | E Bike Wheel Lock | E Bike Wheel Lock |
| SKU Positioning | Compact Standard Motor Hub Lock | High-Torque 15 x 15 mm Motor Hub Lock | High-Temperature 17.2 x 17.2 mm Motor Hub Lock |
| Voltage | 5V DC / 48V DC | 5V DC / 48V DC | 5V DC / 48V DC |
| Communication | UART / RS485 / CAN | UART / RS485 / CAN | UART / RS485 / CAN |
| Speed Sensing Distribution | Defined By Customer Requirement / Motor End Cover, 4 Magnets Evenly Distributed Recommended | Defined By Customer Requirement / Motor End Cover, 4 Magnets Evenly Distributed Recommended | Defined By Customer Requirement / Motor End Cover, 4 Magnets Evenly Distributed Recommended |
| Torque Resistance | >=160 N.m | >=300 N.m | >=300 N.m |
| Axle Hole Size | 15 x 15 mm | 15 x 15 mm | 17.2 x 17.2 mm |
| Operating Temperature | -20°C To 85°C | -20°C To 85°C | -20°C To 100°C, Short-Time -40°C To 125°C For 1 Hour To Be Confirmed By Project |
| Waterproof Rating | IPX6 | IPX6 | IPX6 |
| Mounting Position | Inside Rear Hub Motor, Motor Matching Required | Inside Rear Hub Motor, Motor Matching Required | Inside Rear Hub Motor, Motor Matching Required |
Q: Is this a single new model?
A: No. This is a P2 buyer-intent page comparing HS3718, DS3710 and GS3646 reference directions.
Q: How should the final model be selected?
A: Select according to axle-hole size, torque requirement, operating temperature, motor end-cover design, voltage and communication protocol.
Q: Can the three models share one parameter table?
A: No. The page should use a comparison table and keep each model's parameters separate.
Q: Where are these locks installed?
A: They are installed inside the rear hub motor, and motor matching is required.
Q: What is the common waterproof rating?
A: The source parameters list IPX6 for HS3718, DS3710 and GS3646
